Cover shared idle tracker behavior:
- tracker lifecycle (new, idle after timeout, touch resets)
- read/write with data touches tracker
- read retries on timeout when tracker is not idle
- read closes on timeout when tracker is idle
- shared tracker prevents false timeout across directions

connIdleTimeout previously set per-direction deadlines independently.
During media downloads the client→telegram direction can be idle at the
application level while telegram→client is actively streaming data.
After IdleTimeout (default 1 min) the idle direction's ReadDeadline
fires, tearing down the entire relay and breaking media transfers.

Replace the per-direction timeout with a shared atomic timestamp that
both pump goroutines update on any successful Read or Write. When a
ReadDeadline fires on the idle direction, we check the shared tracker:
if the other direction was recently active, we retry instead of closing.
The connection is only torn down when both directions are idle for the
full timeout period.

This matches the documented IdleTimeout contract: "if we have any
message which will pass to either direction, a timer is reset."

Overhead: one atomic.Int64 (8 bytes) per connection pair, one
atomic.Store (~1 ns) per Read/Write with data, zero extra goroutines.

Fixes #423

Build release artifacts in CI

Decrease a relay buffer size for MIPS devices

fix: apply idle timeout to Telegram relay

Wrap both sides of the Telegram relay in connIdleTimeout,
same as already done for domain fronting in #416.

Without this, if a client disappears (network drop, battery dies),
the TCP connection stays formally alive and the goroutine in the
worker pool blocks on io.CopyBuffer indefinitely. Under mass client
disconnects this accumulates zombie goroutines.

Fixes #417

Remove clock goroutine

This is a followup for https://github.com/9seconds/mtg/issues/412 it
makes sense to manage timers inplace instead of creating for new
goroutines: saves memory

Add public-ipv4/public-ipv6 config options

fix: prevent index out of range panic on 32-bit platforms

fix: apply idle timeout to domain fronting relay

Reduce per-connection memory overhead

On some servers ifconfig.co is unreachable (e.g. Hetzner, AdGuard DNS
blocklists), causing 'mtg doctor' SNI-DNS check and 'mtg access' link
generation to fail. New config options allow specifying public IPs
manually, with automatic detection as fallback.

Fixes #405

- avoid deprecated DefaultIdleTimeout, use time.Minute directly
- simplify embedded field selectors (QF1008)

When the worker pool rejected a connection (ErrPoolOverload), the
accepted net.Conn was never closed — leaking a file descriptor and
TCP socket per rejected connection. Under sustained traffic spikes this
compounds the problem: leaked descriptors reduce the capacity for new
dials (including to the fronting domain), accelerating the failure
cascade described in #378.

Domain fronting relay (for non-Telegram traffic) had no idle timeout,
causing worker pool exhaustion under traffic spikes.

The ProxyOpts.IdleTimeout field existed but was never wired into the
proxy. Now domain fronting connections are wrapped with per-read/write
deadlines reset to the configured idle timeout (default 1m), so stale
or slowloris-style connections are reaped promptly.

Fixes #378

On 32-bit architectures (e.g. ARM7), int is 32 bits wide.
Casting a uint32 hash value to int can overflow, producing a
negative number. Go's modulo operator preserves the sign, so
the channel index can become -1, causing a panic.

Perform the modulo in uint32 space before indexing to ensure
the result is always non-negative.

Fixes #413

- Use sync.Pool for relay buffers instead of stack-allocated arrays.
  A [16379]byte on the goroutine stack forces Go to grow it to 32KB
  (next power of two). Pooled buffers keep goroutine stacks small.

- Same fix for doppelganger write buffer ([16384]byte in conn.start).

- Replace idle goroutines with context.AfterFunc in proxy.ServeConn
  and relay.Relay. These goroutines existed only to wait on ctx.Done()
  and close connections. AfterFunc achieves the same without allocating
  a goroutine until the context is actually cancelled.

Net effect: at 3000 concurrent connections on a 1-vCPU/961MB VPS,
the unmodified binary drops 246 connections and falls to 10 MB/s.
With these changes: zero failures, 63 MB/s, 31% lower RSS.

Closes #412

Add dynamic cert noise calibration for FakeTLS handshake

Instead of a separate cert_probe.go that duplicates the scout's TLS
connection logic, measure the cert chain size directly from the same
HTTPS connections the scout already makes.

Changes:
- Extend ScoutConnResult with payloadLen field
- Add Write interception to ScoutConn for handshake boundary detection
- Scout.learn() now computes cert size (sum of ApplicationData between
  CCS and first client Write) alongside inter-record durations
- Ganger aggregates cert sizes across raids and exposes NoiseParams()
  via atomic pointer for lock-free reads from proxy goroutines
- Proxy reads NoiseParams from Ganger on each handshake instead of
  probing at startup
- Remove cert_probe.go, disk cache, and related config options
  (noise-cache-path, noise-cache-ttl, noise-probe-count)

Falls back to legacy 2500-4700 range until the first scout raid
completes (typically within 1-2 seconds of startup).

The hardcoded noise range (2500-4700 bytes) in the FakeTLS ServerHello
does not match the real certificate chain sizes of many popular fronting
domains (e.g., dl.google.com ≈ 6480 bytes, microsoft.com ≈ 13004 bytes).
This makes the proxy detectable by DPI systems that compare the
ApplicationData size with the real cert chain size for the SNI domain.

On startup, probe the fronting domain's actual TLS handshake size and
use the measured value ± jitter instead of the static range. Falls back
to the legacy 2500-4700 range if the probe fails.

Also adds optional caching of probe results between restarts
(noise-cache-path, noise-cache-ttl) and a configurable probe count
(noise-probe-count) under [defense.doppelganger].

Closes #408

Update stale codeql configuration

Update PGO

Fix build with profiling

Allow using directory bind mounts for a docker container

This helps with a situation when some applications do not allow mounting
individual files, but whole directories. In that case users could mount
`/config` directory with a single file, `config.toml`: `-v
/path/to/dir:/config`. Also, there is a backward compatibility to using
a single `/config.toml`